Pistol Gunsmithing
Please note that the prices listed below are estimates. Actual rates may vary depending on complexity of the job. There may be times when a specialist may be required to perform a particular job, so shipping charges may apply.
|
SERVICES TYPE | PISTOL/REVOLVER SERVICES | RETAIL MINIMUM | RETAIL MAXIMUM |
|---|---|---|---|
| Accuracy | Sight in revolver or pistol | $35 | $35 |
| Barrel Work | Pistol barrel installation | POR | POR |
| Barrel Work | Recrown pistol barrel | $85 | $85 |
| Barrel Work | Remove squib round from barrel | $20 | $20 |
| Glock's | Install Glock crossbar safety trigger | $45 | $45 |
| Glock's | Install Glock front & rear sights | $40 | $40 |
| Glock's | Switch mag release for Glock | $20 | $20 |
| Glock's | Install trigger bar connector or trigger spring. | $30 | $40 |
| M&P's | Install APEX trigger on S&W M&P and Sigmas | $40 | $40 |
| M&P's | Install APEX sears & springs on S&W M&P and Sigmas | $40 | $40 |
| Glock or M&P | Switch mage release to Left Hand on Glocks or M&P | $20 | $20 |
| Sights | Fit sight to existing dovetail | $30 | $30 |
| Sights | RMR installation and slide cuts | POR | POR |
| Trigger Work | Carry gun trigger job | $90 | $90 |
| Trigger Work | Target gun trigger job | $150 | $160 |
| 1911's | Mill for Novak or Bomar sights | $120 | $150 |
| 1911's | Covert 1911 frame to round butt (blued is extra) | $100 | $100 |
| 1911's | Fit 1911 Barrel bushing | $100 | $100 |
| 1911's | throat & polish 1911 barrel (test fire will be needed) | $80 | $80 |
| 1911's | Install stake on front sight | $60 | $60 |
| 1911's | Cut 1911 front sight dovetail | $70 | $70 |
| 1911's | Serrate front of pistol slide (blued is extra) | $100 | $100 |
| 1911's | Fit 1911 thumb safety | $65 | $65 |
| 1911's | Fit 1911 ambidextrous safety | $80 | $80 |
| 1911's | Cut frame for Beaver tail grip safety (blued is extra) | $140 | $140 |
| 1911's | Open 1911 Ejection port (test fire will be needed) | $60 | $80 |
| 1911's | Restake 1911 Plunger Tube | $45 | $45 |
| 1911's | Fit & set 1911 oversized trigger | $80 | $100 |
| 1911's | Install 1911 ejector (will need test fired) | $45 | $45 |
| 1911's | refit & tune new or existing extractors | $445 | $65 |
| 1911's | Install custom pistol barrel | POR | POR |
| 1911's | Install custom hammer & sears | POR | POR |
| Revolver | Retime Colt revolver handgun | $100 | $150 |
| Revolver | Retime S&W revolver | $80 | $120 |
| Revolver | Revolver barrel installation | POR | POR |
| Revolver | Convert revolver frame to round butt (blued is extra) | $70 | $70 |
| Revolver | Straighten crane on revolver | $50 | $50 |
| Revolver | recrown revolver barrel | $80 | $80 |
| Revolver | Bob revolver hammer | $40 | $40 |
| Revolver | Reset end shake | $60 | $60 |
| Revolver | Install & fit new oversized cylinder lock | $70 | $70 |
| Revolver | Install free spin pawl | $80 | $80 |
| Revolver | Cowboy action job | $150 | $150 |
| Revolver | fit wood or ivory grips to single action Revolver | POR | POR |